top of page
AdobeStock_38999421.jpeg

ATEC SHIELDING

Established in 1986

Over 4 Million Square Feet of Shielding Provided

HEMP | EMP | RF | I/EMI

Sub-Systems Construction

Shielding Protection

Federal | Private | Infrastructure

HEMP EVENT
Construction Site
AdobeStock_564756672.png

THE CONTINUED THREATS AND NECESSITY FOR
HEMP SHIELDING COUNTERMEASURES

HEMP
HIGH-ALTITUDE ELECTRO MAGNETIC PULSE

High-altitude Electro-Magnetic Pulse (HEMP)

is a mass amount of radiation generated by a nuclear weapon detonation in space or the earth's upper atmosphere. HEMP events have devastating effects on any electronic equipment within its sphere of influence. HEMP SHIELDING is a proven and time tested sub-system that mitigates this threat.

WHAT WE DO

WHAT WE DO
AdobeStock_45123263.jpeg

DESIGN

Our management team has over 150 years of Shielding, Structural, Civil, Electrical, and Mechanical Systems Experience. With a full in-house capabilities to effectively design our shielding systems within any facility.

We work closely with Architects, Engineers, Design Consultants, End Users, and General Contractors to deliver an effective and constructible design in any condition.

DESIGN
Construction Site

CONSTRUCTION

We specialize in Shielding Construction that consists of fully RF welded steel envelopes of various thickness and sizes to meet the higher performance requirements of various Federal Government agencies as well as Private Sector Infrastructure and Defense.

We pride ourselves in having highly experienced field project management team that has safety and successfully delivered HEMP SHIELDING projects for the past 3 decades and continues to do so.

Steel welding in tube.png
CONSTRUCTION
FABRICATION
Construction Site
welder fab 2.png

FABRICATION

ATEC maintains a 90,000 Square Foot fabrication facility located in Columbia, MD that includes a 5 ton bridge crane, paint booth, RF testing chamber, and full production and welding capabilities.

Our core shop QAQC Team, RF Welders, and Fabrication Staff have been working with ATEC for DECADES with a vast amount of RF Welding and Fabrication experience to include custom waveguides, steel assemblies and structural panels.

TESTING
Construction Site

TESTING & CERTIFICATION

Extensive knowledge and experience of Division 13 and all the testing that may be required. Years of lessons learned, Research and Development of materials, means, and methods that are best suited for each testing requirement.

Testing Standards:

MIL STD 188-125-1A | MIL HANBOOK 412 | IEEE99 | IDS IDC 705 | NSA 95

AdobeStock_611046695.jpeg
PROJECTS

PROJECTS PORTFOLIO

ABOUT US
AdobeStock_619965387.png

ABOUT US

ATEC was founded in 1986 in the state of Maryland and has successfully designed, installed, and tested over millions cubic feet of RF Shielding.  Projects have ranged from small RF test enclosures to complete RF Shielding of entire multistory buildings.

 

Our Projects demonstrate ATEC’s ability to construct, test and certify large, complex HEMP Shielding Systems and is a testament in our ability to construct vastly complex buildings in the face of the most adverse conditions. 

Construction Site
C2 Space.png

EXPERIENCE
SNAPSHOT

CERTIFIED SHIELDING ENCLOSURE CONSTRUCTION

• Carbon Steel Plate of All Thickness

• 1/4" 6061 Aluminium Plate

• Fabrics & Foils

• Steel Laminated Plywood "Hats & Flats"

• Power Filters - Signal Filters

• Wave Guides : Honeycomb - Drilled Array - Welded Array

• HEMP Doors : Knife Edge - Air Bladder - Interlock Controls

• HEMP Conduit - Manholes - Junction Boxes

• SELDS Systems

• Embedded Antenna Systems

• Dielectric Isolation

• Full turn key Non-Permanent HEMP/SCIF Command Centers
& Power Plant - ISO Container Fit Outs

Address

7020 Columbia Gateway Drive

Columbia, MD 21046

Phone

443.459.5080

Fax

443.459.5090

Email

bottom of page